You’ll get the unloaded wheel lifting during cornering if the suspension is too stiff. What is happening is there isn’t enough travel on the springs to keep the wheel on the ground
Hyone M2.Concept-GT4 (2007)
The M2 (sort of copied from BMW, ignore) Concept features some futuristic yet old school design so it should stand out from the rest (hopefully). Car never made it into a race as this again is the concept. Too lazy to do livery, hence why it’s a concept.
2007 BSC Arrow
My first entry is a lightweight fibreglass coupe with a high revving V6 engine
Technical Specifications
Length | 3.91m |
Width | 1.72m |
Wheelbase | 2.27m |
Weight | 980KG |
Chassis | steel monocoque |
Panels | Fibreglass |
Front Suspension | Double wishbone with gas mono-tube dampers |
Rear Suspension | Double wishbone with gas mono-tube dampers |
Front Brakes | 300mm ventilated, four calipers |
Rear Brakes | 300mm vented discs, single caliper |
Steering | manual rack and pinion |
Front Tyres | P235 50R16 99Y Radial |
Rear Tyres | P235 50R16 99Y Radial |
Engine | 2597cc V6 with sequential multi point fuel injection and performance intake |
Transmission | six speed single clutch automated manual with geared lsd |
Power | 244bhp@7000rpm |
Torque | 268NM@4900rpm |
2007 EV-lution Type B
My second entry is a bit of a bare design tbh, but it’s supposed to be a converted kit car so that’s my excuse for it being plain.
Technical Specifications
Length | 3.73m |
Width | 1.87m |
Wheelbase | 2.33m |
Weight | 1150KG |
Chassis | steel monocoque |
Panels | Fibreglass |
Front Suspension | Double wishbone with gas mono-tube dampers |
Rear Suspension | Double wishbone with gas mono-tube dampers |
Front Brakes | 275mm ventilated discs, four calipers |
Rear Brakes | 275mm ventilated discs, single caliper |
Steering | manual rack and pinion |
Front Tyres | P225 50R16 99S Radial |
Rear Tyres | P245 45R16 101S Radial |
Engine | 159kW brushless motor with integrated motor controller. 20kWh litium ion battery pack mounted in rear engine space. |
Transmission | single speed reduction gear with geared lsd |
Power | 159kW motor |
Torque | 305NM@0000rpm |
Is this standard steel, or a fancier type (galvanized at least)? And does this apply to both of your entries?
Also, from the spec sheet, I can infer that you used the !ev! modifier for the Beam portion, but the pictures show that it’s built on the smallest of the '98 Stradale body sets (~2.3m wheelbase) - the same as the one I used for my second PAIN entry, but presumably in a different bodystyle (targa instead of fixed-roof coupe).
It’s the fixed roof inset variant, it’s the same style as the targa one though.
They are both plain steel, for that sort of “rust from inside” thing you get from a lot of fibreglass cars
Edit
Also I didn’t realise your car was built on the stradale body, you’ve managed to hide the square back of the car
The use of regular steel for the chassis of both your entries makes sense - it’s meant to save costs.
As for disguising the usually angular rear of the Stradale body sets, I adjusted the rear corner morphing zones to make them more rounded, and placed a body molding fixture on the upper edge of the rear end in 3D fixture mode to make it resemble a lip spoiler - the same trick I used for the LVC LS60, except that the LS40 I entered in PAIN has two circular taillight lenses instead of just one.
1 week to go! @mart1n2005 i’ll check your cars soon, quick question though. Do electric cars have any advantage?
electric cars give disadvantage, making your car extremely slow
Alright, my final entry. Basically a Porsche, but i tried to alter some stuff to not make it too much like a Porsche. It’s good It has an NA Inline 3, so I hope it will surprise some people on the track.
The car is run by Team Texoline.
That’s why although the !ev! modifier is permitted here, it wouldn’t be advisable to actually use it.
Due to the reduced amount of entries in this challenge, a few options have opened up for me, the runs, and the video.
Should i make 1 minute reviews in the video instead, and use longer tracks? All advice is useful!
(I don’t mind a more relaxing challenge for once, that even 1 person enters means more than enough lmao)
2000 Mara Asteri Group A
Aiming for GT4, but finding leftover, but perfectly serviceable Group A racing cars from the 1990s…
… even with true racing pedigree
Just have to chop off / replace some aero, cheapen out some $10000 worth of parts, what can possibly go wrong?
Wait a second. Kotatsu? As in the warm table? Looks great though, love it. Expect a possibility of 2 10s on styling and maybe even an 11.
ah my bad lol the 2nd one was from the other brand, edited it just now
Got a few entries recently and since i dont feel like DMing everyone, they’re all legal!
I have a car that I will not be able to finish, currently making ~420 hp and weighs more or less nothing so if anyone wants it please tell me so you can finish and enter it